Відео

its funny, you break down that the 69710-48010 is for the door latch, but when you look for that part, seemingly anywhere, it states its for the lock.

On day 5 now I wanna raw dawg the engineers wife who designed this

My frontier just died on me and wont start. This video is really helpful, Ill be trying this over the weekend.

About how much gas would you want in the tank. I just didn't think you would want it full but could be wrong

Where did you buy the servos

Thank you for a great video much appreciated very very helpful!!👍👌🙏

It's is a b...ch to take out! Thank you for the advice. 🙂

Very helpful.......much appreciate your effort in posting this video.

Hey dude my cable is not broken

Fantastic idea! I have a Ranger with the leaky servo seal. Been running it with a low fluid level for the last few years with no problem, but it's time to finally get to it.

Where does the ac switch negative wire gone after thermostat

Tom I have 2004 Honda Civic Hove no AC what will be the cost to install AC.

Hey same car but my ac light is not coming all the fuse is good, but no ground signal coming from the ac button when you press it. And I am getting two ground signal when I plug off the connector behind the ac button and one live signal (positive signal),but when I put positive current to the single wire that connects to the ac compressor the ac works how do I fix that .Note no light in display when I touch the ac button

what makes this happen that you need to have it done and how many miles did you have on that car at the time.

Just what I needed to hear. I have a cub cadet same trouble with Kohler engine (courage).

My nissan frontier the problem is when I crank the Rotor of the distributor no turn so I remove and i can spin it with my hand but when I put it back no spin si what can be the problem?

Good morning ..A problem with the two yellow 20 fuses are good but no current underneath .How can I do to solve this problem...Thank you so much..Hope to have an answer with you Sir..Watching from France..

Shit cu. Fix my car i got da same pro yo haha

Tom, mine squeaks only when ac is on ? Normal fan doesn’t make noise, only ac mode

Why did you remove engine mounts Uneccessary

Thanks that was my problem also.Easy fix.

THANK YOU GOD BLESS YOU

3 years later. Saw this video 4 pounds hammer and a chisel and works. My axel was destroyed thanks for the tip

You damn near had 2 take apart the whole car

Was your transmission light on in the dash???

15 yeas fords had tghis rear hatch problem i have a 93 and have fixed it 4 times in 2 years

Well done thanks

Hello I switched out the solenoids and codes are gone but the car goes forward in reverse and neutral. It still does go forward in drive. The fluid is topped off and I checked at the transmission and can see the shift linkage moving the transmission though gears. When it's in reverse the reverse lights do come on. I've replaced the transmission filter aswell. Before doing the shift solenoids the car worked properly just had the code. And when I replaced solenoids I replaced all 3 even though only my first one was bad. Can anyone point me in the right direction of what to check, I'm assuming has to be a hydraulic issue but I've seen online this has happened to others after this procedure but no posted fixes or causes. Please help 🙏🏽

Gracias por el video ha sido de gran ayuda, excelente explicación.

I was quoted $600 USD to replace the oil filter housing gaskets from a well reputable mechanic shop, is that reasonable for this type of repair?

How much will you charge to fix my '06 with 87K 😂😂😂

I've Nissan Xterra 2011. It starts fine in the morning and after driving it 15-20 minutes when I stop the car and restart, it takes long cranking. I have got knock sensors, camp sensors and crank sensor replaced. What would be the possible problem?

Does it have a secondary external Fuel filter also?

Couldn’t get the 12v accessory power outlet off to remove the panel so I gave up 🤦‍♂️ now I’m hoping it’s the brake light switch under the brake and could figure that out. Wasn’t the fuse

Thorough and clear information! Thank you sir!

Yea I’ll definitely pay the 150 or whatever to much work 🤣

You said to align the alignment bolts (at 7:50) to set the manual valve, and to find how online. I cannot find any info on this procedure. How exactly is the manual valve positioned?

The AC not cutting

This is a great video but NO perspective given in where the thing is located. In the dark zoomed in two inches away from the part doesn’t give a clue to where to find this thing.

Thanks brother

Hi Tom, what was the problem with the old sensor and how did you diagnose? Thanking you in advance.

Yes that did help thank-you.

Great help, thanks!

Hey thank you for your help, bud. This actually assisted me a good amount

Hello, I just bought a 2010 Cobalt yesterday that doesn't want to shift into first gear. I need to be rolling enough just to catch second gear then it slips for a second then goes to 3rd gear. It drives ok once I get to 4th . If I'm on a hill I'm pretty much Fd if people are behind me. The only code that came up is Power Train System "U0073 -00 control module communicator bus" but there is no engine light on the dash. Do you think this could be the problem hopefully? The guy I bought it from said it just started happening suddenly. Please lmk? Great video and Subbed!

Just made my day better thanks

But what does it sound like?

ive done plugs on those from bottom without taking anything out

gotta do those plugs from the bottom ma dude its easy